View LD1085D2M15_241708.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LD1085 SERIES
3A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED
I I
I
I
I I
I
I
TYPICAL DROPOUT 1.3V (AT 3A) THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 3.6V, 5V, 8V, 9V, 12V. GUARANTEED OUTPUT CURRENT UP TO 3A OUPUT TOLERANCE 1% AT 25C AND 2% IN FULL TEMPERATURE RANGE INTERNAL POWER AND THERMAL LIMIT WIDE OPERATING TEMPERATURE RANGE -40C TO 125C PACKAGE AVAILABLE: TO-220, TO-220FP D2PAK, D 2PAK/A PINOUT COMPATIBILITY WITH STANDARD ADJUSTABLE VREG
TO-220
TO-220FP
D2PAK
D2PAK/A
DESCRIPTION The LD1085 is a LOW DROP Voltage Regulator able to provide up to 3A of Output Current. Dropout is guaranteed at a maximum of 1.2V at the maximum output current, decreasing at lower loads. The LD1085 is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance.
A 2.85V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the LD1085 quiescent current flows into the load, so increase efficiency. Only a 10F minimum capacitor is need for stability. The device is supplied in TO-220, TO-220FP, D2PAK and D2PAK/A. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within 1% at 25C.
Figure 1: Schematic Diagram
March 2005
Rev. 14
1/19
LD1085 SERIES
Figure 2: Pin Connection (top view)
TO-220
TO-220FP
D2PAK Table 1: Order Codes
TO-220 LD1085V15 LD1085V18 LD1085V25 LD1085V28 LD1085V33 LD1085V36 LD1085V50 LD1085V80 LD1085V90 LD1085V12 LD1085V TO-220FP LD1085P15 LD1085P18 LD1085P25 LD1085P28 LD1085P33 LD1085P36 LD1085P50 LD1085P80 LD1085P90 LD1085P12 LD1085P D2PAK (*) LD1085D2T15 LD1085D2T18 LD1085D2T25 LD1085D2T28 LD1085D2T33 LD1085D2T36 LD1085D2T50 LD1085D2T80 LD1085D2T90 LD1085D2T12 LD1085D2T
D2PAK/A
D2PAK/A (*) LD1085D2M15 LD1085D2M18 LD1085D2M25 LD1085D2M28 LD1085D2M33 LD1085D2M36 LD1085D2M50 LD1085D2M80 LD1085D2M90 LD1085D2M12 LD1085D2M
OUTPUT VOLTAGE 1.5 V 1.8 V 2.5 V 2.85 V 3.3 V 3.6 V 5.0 V 8.0 V 9.0 V 12.0 V ADJ
(*) Available in Tape & Reel with the suffix "R" for fixed version and "-R" for adjustable version.
Table 2: Absolute Maximum Ratings
Symbol VI IO PD Tstg Top DC Input Voltage Output Current Power Dissipation Storage Temperature Range Operating Junction Temperature Range Parameter Value 30 Internally Limited Internally Limited -55 to +150 -40 to +125 Unit V mA mW C C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied.
2/19
LD1085 SERIES
Table 3: Thermal Data
Symbol Rthj-case Rthj-amb Parameter Thermal Resistance Junction-case Thermal Resistance Junction-ambient TO-220 3 50 D2PAK 3 62.5 Unit C/W C/W
Figure 3: Application Circuits
R2 VO = VREF (1 + ) R1
Table 4: Electrical Characteristics Of LD1085#15 (VI=4.5V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 5AVI = 3.1 to 30V (note 1) IO = 0 mA VI = 3.1 to 18V IO = 0 mA VI = 3.1 to 15V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 7.5 3V TA = 25C f =10Hz to 10KHz IO = 3A 60 3.2 0.2 TJ = 25C Min. 1.485 1.47 Typ. 1.5 1.5 0.2 0.4 2 4 1.3 5 4.5 0.5 0.008 72 0.003 0.5 0.5 0.04 Max. 1.515 1.53 4 4 10 20 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
3/19
LD1085 SERIES
Table 5: Electrical Characteristics Of LD1085#18 (VI=4.8V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 5AVI = 3.4 to 30V (note 1) IO = 0 mA VI = 3.4 to 18V IO = 0 mA VI = 3.4 to 15V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 7.5 3V TA = 25C f =10Hz to 10KHz IO = 3A 60 3.2 0.2 TJ = 25C Min. 1.782 1.764 Typ. 1.8 1.8 0.2 0.4 2 4 1.3 5 4.5 0.5 0.008 72 0.003 0.5 0.5 0.04 Max. 1.818 1.836 4 4 10 20 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
Table 6: Electrical Characteristics Of LD1085#25 (VI=5.5V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 4.1 to 30V (note 1) IO = 0 mA VI = 4.1 to 18V IO = 0 mA VI = 4.1 to 18V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 7.5 3V TA = 25C f =10Hz to 10KHz IO = 3A 60 3.2 0.2 TJ = 25C Min. 2.475 2.45 Typ. 2.5 2.5 0.2 0.4 2 4 1.3 5 4.5 0.5 0.008 72 0.003 0.5 0.5 0.04 Max. 2.525 2.55 4 4 10 20 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
4/19
LD1085 SERIES
Table 7: Electrical Characteristics Of LD1085#285 (VI=5.85V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 4.5 to 30V (note 1) IO = 0 mA VI = 4.5 to 18V IO = 0 mA VI = 4.5 to 18V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 7.85 3V TA = 25C f =10Hz to 10KHz IO = 3A 60 3.2 0.2 TJ = 25C Min. 2.821 2.793 Typ. 2.85 2.85 0.2 0.5 3 7 1.3 5 4.5 0.5 0.008 72 0.003 0.5 0.5 0.04 Max. 2.879 2.907 6 6 15 20 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
Table 8: Electrical Characteristics Of LD1085#33 (VI=6.3V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 4.9 to 30V (note 1) IO = 0 mA VI = 4.9 to 18V IO = 0 mA VI = 4.9 to 18V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 8.3 3V TA = 25C f =10Hz to 10KHz IO = 5A 60 3.2 0.2 TJ = 25C Min. 3.267 3.234 Typ. 3.3 3.35 0.5 1 3 7 1.3 5 4.5 0.5 0.008 72 0.003 0.5 0.5 0.04 Max. 3.333 3.366 6 6 15 20 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
5/19
LD1085 SERIES
Table 9: Electrical Characteristics Of LD1085#36 (VI=6.6V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 5.2 to 30V (note 1) IO = 0 mA VI = 5.2 to 18V IO = 0 mA VI = 5.2 to 18V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 8.6 3V TA = 25C f =10Hz to 10KHz IO = 3A 60 3.2 0.2 TJ = 25C Min. 3.564 3.528 Typ. 3.6 3.6 0.5 1 3 7 1.3 5 4.5 0.5 0.008 72 0.003 0.5 0.5 0.04 Max. 3.636 3.672 10 10 15 20 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
Table 10: Electrical Characteristics Of LD1085#50 (VI=8V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 6.6 to 30V (note 1) IO = 0 mA VI = 6.6 to 20V IO = 0 mA VI = 6.6 to 20V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 10 3V TA = 25C f =10Hz to 10KHz IO = 3A 60 3.2 0.2 TJ = 25C Min. 4.95 4.9 Typ. 5 5 0.5 1 5 10 1.3 5 4.5 0.5 0.008 72 0.003 0.5 0.5 0.04 Max. 5.05 5.1 10 10 10 35 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
6/19
LD1085 SERIES
Table 11: Electrical Characteristics Of LD1085#80 (VI=11V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 9.8 to 30V (note 1) IO = 0 mA VI = 9.8 to 20V IO = 0 mA VI = 9.8 to 20V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 13 3V TA = 25C f =10Hz to 10KHz IO = 3A 54 3.2 0.2 TJ = 25C Min. 7.92 7.84 Typ. 8 8 1 2 8 12 1.3 5 4.5 0.5 0.008 71 0.003 0.5 0.5 0.04 Max. 8.08 8.16 18 18 30 60 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
Table 12: Electrical Characteristics Of LD1085#90 (VI=12V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 11 to 30V (note 1) IO = 0 mA VI = 11 to 20V IO = 0 mA VI = 11 to 20V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 14 3V TA = 25C f =10Hz to 10KHz IO = 3A 54 3.2 0.2 TJ = 25C Min. 8.91 8.82 Typ. 9 9 1 2 8 12 1.3 5 4.5 0.5 0.008 70 0.003 0.5 0.5 0.04 Max. 9.09 9.18 20 20 30 60 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
7/19
LD1085 SERIES
Table 13: Electrical Characteristics Of LD1085#12 (VI=15V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Thermal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 0 mA TJ = 25C IO = 0 to 3AVI = 13.8 to 30V (note 1) IO = 0 mA VI = 13.8 to 25V IO = 0 mA VI = 13.8 to 25V IO = 0 to 3ATJ = 25C IO = 0 to 3A IO =3 A VI 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, VI = 17 3V TA = 25C f =10Hz to 10KHz IO = 3A 54 3.2 0.2 TJ = 25C Min. 11.88 11.76 Typ. 12 12 1 2 12 24 1.3 5 4.5 0.5 0.008 66 0.003 0.5 0.5 0.04 Max. 12.12 12.24 25 25 36 72 1.5 10 Unit V V mV mV mV mV V mA A A %/W dB % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
Table 14: Electrical Characteristics Of LD1085# (VI=4.25V, CI = CO =10F, TA = -40 to 125C, unless otherwise specified.)
Symbol VO VO VO Vd IO(min) Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Minimum Load Current Short Circuit Current Thermal Regulation SVR IADJ IADJ eN S S Supply Voltage Rejection Adjust Pin Current Adjust Pin Current Change RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability Test Conditions IO = 10mA TJ = 25C IO = 10mA to 5AVI = 2.85 to 30V (note 1) IO = 10mA VI = 2.85 to 16.5V TJ = 25C IO = 10mA VI = 2.85 to 16.5V IO = 10mA to 5ATJ = 25C IO = 0 to 5A IO = 5A VI = 30V VI - VO = 5V VI - VO = 25V TA = 25C, 30ms pulse f = 120 Hz, CO = 25 F, CADJ = 25 F, IO = 5A VI = 6.25 3V VI = 4.25V IO = 10 mA IO = 10mA to 5A VI = 2.85 to 16.5V (note 1) TA = 25C f =10Hz to 10KHz 60 5.5 0.5 Min. 1.237 1.225 Typ. 1.25 1.25 0.015 0.035 0.1 0.2 1.3 3 6.5 0.7 0.003 72 55 0.2 0.003 0.5 0.5 120 5 0.015 Max. 1.263 1.275 0.2 0.2 0.3 0.4 1.5 10 Unit V V % % % % V mA A A %/W dB A A % % %
TA = 125C 1000Hrs
NOTE 1: See short-circuit current curve for available output current at fixed dropout.
8/19
LD1085 SERIES
TYPICAL CHARACTERISTICS (unless otherwise specified Tj = 25C, CI=CO=10F) Figure 4: Output Voltage vs Temperature Figure 7: Short Circuit Current vs Dropout Voltage
Figure 5: Output Voltage vs Temperature
Figure 8: Line Regulation vs Temperature
Figure 6: Output Voltage vs Temperature
Figure 9: Load Regulation vs Temperature
9/19
LD1085 SERIES
Figure 10: Dropout Voltage vs Temperature Figure 13: Quiescent Current vs Temperature
Figure 11: Dropout Voltage vs Output Current
Figure 14: Dropout Voltage vs Output Current
Figure 12: Adjust Pin Current vs Temperature
Figure 15: Supply Voltage Rejection vs Output Current
10/19
LD1085 SERIES
Figure 16: Supply Voltage Rejection vs Frequency Figure 19: Stability
Figure 17: Supply Voltage Rejection vs Temperature
Figure 20: Stability
Figure 18: Minimum Load Current vs Temperature
Figure 21: Line Transient
VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), CADJ = 1F
11/19
LD1085 SERIES
Figure 22: Line Transient Figure 24: Load Transient
VI=12 to 13V, IO=200mA, CI = 1F(tant), CO=10F(tant), CADJ =1F
VI=12 V, I O=0.12 to 3 A, CI = 1F(tant), CO=10F(tant) CADJ =1F
Figure 23: Load Transient
VI=12 V, I O=0.12 to 3 A, CI = 1F(tant), CO=10F(tant) CADJ =1F
12/19
LD1085 SERIES
TO-220 MECHANICAL DATA
DIM. A C D D1 E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 DIA. 13.0 2.65 15.25 6.2 3.5 3.75 0.49 0.61 1.14 1.14 4.95 2.4 10.0 16.4 14.0 2.95 15.75 6.6 3.93 3.85 0.511 0.104 0.600 0.244 0.137 0.147 mm. MIN. 4.40 1.23 2.40 1.27 0.70 0.88 1.70 1.70 5.15 2.7 10.40 0.019 0.024 0.044 0.044 0.194 0.094 0.393 0.645 0.551 0.116 0.620 0.260 0.154 0.151 TYP MAX. 4.60 1.32 2.72 MIN. 0.173 0.048 0.094 0.050 0.027 0.034 0.067 0.067 0.203 0.106 0.409 inch TYP. MAX. 0.181 0.051 0.107
P011C
13/19
LD1085 SERIES
TO-220FP MECHANICAL DATA
mm. DIM. A B D E F F1 F2 G G1 H L2 L3 L4 L5 L6 L7 DIA. 28.6 9.8 2.9 15.9 9 3 MIN. 4.40 2.5 2.5 0.45 0.75 1.15 1.15 4.95 2.4 10.0 16 30.6 10.6 3.6 16.4 9.3 3.2 1.126 0.385 0.114 0.626 0.354 0.118 TYP MAX. 4.60 2.7 2.75 0.70 1 1.50 1.50 5.2 2.7 10.40 MIN. 0.173 0.098 0.098 0.017 0.030 0.045 0.045 0.194 0.094 0.393 0.630 1.204 0.417 0.142 0.645 0.366 0.126 inch TYP. MAX. 0.181 0.106 0.108 0.027 0.039 0.059 0.059 0.204 0.106 0.409
7012510A-H
14/19
LD1085 SERIES
D2PAK MECHANICAL DATA
mm. DIM. MIN. A A1 A2 B B2 C C2 D D1 E E1 G L L2 L3 M R V2 0 4.88 15 1.27 1.4 2.4 0.4 8 0 10 8.5 5.28 15.85 1.4 1.75 3.2 0.192 0.590 0.050 0.055 0.094 0.016 8 4.4 2.49 0.03 0.7 1.14 0.45 1.23 8.95 8 10.4 0.393 0.335 0.208 0.624 0.055 0.068 0.126 TYP MAX. 4.6 2.69 0.23 0.93 1.7 0.6 1.36 9.35 MIN. 0.173 0.098 0.001 0.027 0.044 0.017 0.048 0.352 0.315 0.409 TYP. MAX. 0.181 0.106 0.009 0.036 0.067 0.023 0.053 0.368 inch
P011P6G
15/19
LD1085 SERIES
D2PAK/A MECHANICAL DATA
mm. DIM. MIN. A A1 A2 B B1 B2 C C2 D D1 E E1 G L L2 M R V2 0 4.88 15 1.27 2.4 0.4 8 0 10 8.5 5.28 15.85 1.4 3.2 0.192 0.591 0.050 0.094 0.016 8 4.40 2.49 0.03 0.7 0.8 1.14 0.45 1.23 8.95 8 10.4 0.394 0.335 0.208 0.624 0.055 0.126 TYP MAX. 4.60 2.69 0.23 0.93 1.3 1.7 0.60 1.36 9.35 MIN. 0.173 0.098 0.001 0.028 0.031 0.045 0.018 0.048 0.352 0.315 0.409 TYP. MAX. 0.181 0.106 0.009 0.037 0.051 0.067 0.024 0.054 0.368 inch
7106164/D
16/19
LD1085 SERIES
Tape & Reel D2PAK-P 2PAK-D 2PAK/A-P 2PAK/A MECHANICAL DATA
mm. DIM. MIN. A C D N T Ao Bo Ko Po P 10.50 15.70 4.80 3.9 11.9 10.6 15.80 4.90 4.0 12.0 12.8 20.2 60 14.4 10.70 15.90 5.00 4.1 12.1 0.413 0.618 0.189 0.153 0.468 0.417 0.622 0.193 0.157 0.472 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.421 0.626 0.197 0.161 0.476 0.512 MIN. TYP. MAX. 7.086 0.519 inch
17/19
LD1085 SERIES
Table 15: Revision History
Date 07-Oct-2004 08-Feb-2005 01-Mar-2005 Revision 12 13 14 Description of Changes Mistake Order Codes - Table 1. Mistake U.M. Load Regulation - V ==> mV. Version 1.2V removed.
18/19
LD1085 SERIES
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners (c) 2005 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
19/19

▲Up To Search▲

Price & Availability of LD1085D2M15

	To Download LD1085D2M15 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .